Avia C.2B1
1August 26, 2017The inspiration.
2August 26, 2017The rear control panel installation is problematic, as it sits too high and too far forward.
3August 26, 2017I decided to reposition it down a bit and further back, to clear the resin piece (PUR 6) that spans the cockpit at this location.
4August 26, 2017Piece of styrene did the trick.
5August 26, 2017The control pedals in the rear cockpit sit way too high also. I did not fix this, but it's a consideration when building an open cockpit.
6August 26, 2017Interior was primed with Mr. Surfacer and then airbrushed with Testors Acryl RLM66. Enamel wash was followed by drybrushing with lighter grays.
7August 26, 2017Completed cockpit. The kit comes with a nice PE set that adds needed detail to the cockpit.
8August 26, 2017I did not use all PE parts supplied: I left the pedals as is, and did not add any detail to the cockpit walls (closed canopy will prevent seeing most of this anyway).
9August 26, 2017
10August 26, 2017The part A18 representing the engine is not tall enough. I added a shaped styrene block to the bottom to ensure that the propeller shaft lines up correctly with the front fuselage section, part A17.
11August 26, 2017Undercarriage assembly was straightforward and per instructions.
12
13August 26, 2017Assembling the fuselage and the wings. No issues here.
14September 13, 2017There is a gap between the fuselage and the horizontal stabilizer (nothing a bit of putty can't fix).
15September 13, 2017A propeller jig is needed to assemble the propeller. The propeller hub is resin (2 versions are supplied with the kit, as are 2 propeller blade styles).
16September 13, 2017The resin engine scoops supplied with the kit are too stiff to conform to the fuselage. I replaced them with shaped styrene.
17September 13, 2017There are a number of fiddly PE parts that are butt-joined to the wings. Small pins left on the PE parts, together with mating holes in the plastic, would have made for a much stronger joint.
18September 13, 2017..more fiddlies…
19September 13, 2017Cockpit is ready for the canopy. Conopy fit was very good. I dipped it in Future and glued it on using Krystal-Kleer.
20September 13, 2017Canopy masked using the Montex mask and Vallejo masking fluid. The Montex mask material is stiffer that the competition, and the rear section needed a bit of the masking fluid to close up.
21September 13, 2017Once I was happy with the prime coat (several cycles of PSR were needed), I airbrushed the panel lines with dilluted Testors Acryl Black.
22September 13, 2017
23September 28, 2017All Clad 2 ALC 106 White Aluminum was airbrushed in thin coats to allow pre-shading to show through.
24September 28, 2017Gunze gloss coat from the can was applied the next day as base for the Mark I decals. They went on nicely and needed very short soak to come off the paper. I used the Micro Sol decal solution.
25September 28, 2017Testors Acryl black was airbrushed on the engine panels following required masking.
26September 28, 2017I used dilluted oil paint thinned with lighter fluid to highlight the panel lines and give some depth to the silver.
27September 28, 2017Here, the Raw Umber oil wash after application to the port wing.
28September 28, 2017Landing gear legs fit in a very shallow tubes, so gluing these is tricky, especially since proper positioning is required. I strongly recommned adding metal pins to strengthen the joint.
29September 28, 2017The space between the landing gear leg and the wheel well is too narrow for the wheel well cover: I sanded each cover until it slid into this space.
30September 28, 2017And here are the completed pics.
31September 28, 2017
32September 28, 2017
33September 28, 2017
34September 28, 2017
35September 28, 2017
36September 28, 2017
37September 28, 2017Splatter on the wheel covers and undercarriage is Testors Acryl Raw Umber, Red Earth, and Sand.
38September 28, 2017
39September 28, 2017
Komentáre
27 December 2024, 10:11 -
Album info
I decided to tackle this project mainly to try out all-metal finish using All Clad lacquers. Special Hobby released the Arado Ar-96, of which C.2 is its Czech post-WWII reincarnation, in several versions. I am planning this as an OOB build: closed canopy, no additions, just a decal option from Mark I. decal set that comes with their Arado Ar-96 title.
This turned out to be a pleasurable build. Few surprises, keeping in mind that this is a short-run kit, and some experience is handy during construction. I discuss any specifics in the accompanying pictures.
39 snímky
1:72
dokončený
Avia C-2B-1
Československé vojenské letectvo (Czechoslovak Air Force 1940-1993)1 Sqn., Air Reg. 30 Black LX-8
1949 - Trencianske Biskupice Airfield
Light aluminum finish overall