Zimmerit Coating Sheet for 1/35 Scale Elefant
Tamiya
Tamiya | No. 12644 | 1:35
faktat
- Brändi:
- Tamiya
- otsikko:
- Zimmerit Coating Sheet for 1/35 Scale Elefant Tamiya
- Määrä:
- 12644
- asteikko:
- 1:35
- Tyyppi:
- Yksityiskohta
- julkaisi:
- 2012
- Viivakoodi:
- 4950344126446 (EAN)
- Pakkaus:
- säkkeihin
- Aihe:
- Sd.Kfz. 184 Ferdinand » Tankin tuhoajat (ajoneuvot)
Laatikon sisältö
Tarra-arkki (tarrat)
Mitat:
330x135x1 mm
(13x5.3x0 inch)
Paino:
20 g (0.04 lbs)
Suunniteltu
Tämä jälkimarkkinoiden sarja on suunniteltu:
Tamiya
2012
Ohjeet
ladata 2605Kb (.pdf)
markkinat
No partner shops available
In-box-arviot
Ulkoiset arvostelut
Kommentit
Jens Andrée
I have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.
I have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.
4 July 2017, 01:13
Holger Kranich
Hi Jens,
i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger
Hi Jens,
i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger
4 July 2017, 06:35
Jens Andrée
I badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!
I badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!
4 July 2017, 20:25
projektit
10 kuvien
Sd.Kfz.184 Schwerer Jagdpanzer "Elefant" 1:35
projekti: Sd.Kfz.184 Schwerer Jagdpanzer "Elefant"
Viitemateriaali
Kaikki kirjat » (14 yhteensä) Kaikki kulkureitit » (3 yhteensä)