Airbus A400M "ATLAS"

Revell | No. 04859 | 1:144

Fatos

Marca:: Revell
Título:: Airbus A400M "ATLAS"
Número:: 04859 (Também listado como 80-4859)
Escala:: 1:144
Tipo:: Kit completo
Lançado:: 2014 Produto novo
Código de barras:: 4009803048598 (EAN)
Embalagem:: Caixa (abertura lateral)
Tópico:: Airbus A400M Atlas » Hélice (Aeronave)

Marcações

Airbus A400M Atlas

Airbus A400M Grizzly

Airbus (1970-now)

F-WWMZ
2013

Airbus A400M-180 Atlas

Bundeswehr Luftwaffe (German Air Force 1956-now)

LTG 62 54+01
2014 - Wunstorf

Armée de l'Air (French Air Force 1934-2019)

F-RBAB "Ville de Toulouse"
2014

Conteúdo

Árvore de plástico (Light gray), Árvore de plástico (Clear), Decalque (dágua) (Multi-colored), Instruções (papel) (Black & white)

Dimensões:
537x207x63 mm (21.1x8.1x2.5 inch)

Boxart desenhado por Andrzej Deredos

O que está na caixa »

Linha do tempo do produto

Revell

2014

2024

Produto novo

Conjunto de modelos

História completa »

Instruções

Download 6326Kb (.pdf)

Mercado

No partner shops available

Avaliações

Revisões externas

Avaliação da caixa

IPMS Deutschland

Avaliação da caixa

Modellversium

Avaliação da caixa

Hyperscale

Avaliação

FineScale Modeler Forum

Todos os comentários » (7 no total)

Revistas

Sky Model | 80

Italian (TOC: 11 lines)

December-January 2015

Model Airplane International | 162

English (TOC: 19 lines)

January 2019

Model Airplane International | 115

English (TOC: 9 lines)

February 2015

Todas as revistas » (7 no total)

Comentários

7 January 2025, 16:02 -

Treehugger
Better watch out for those sink marks. Make sure you add some putty around all the windows and sand down before starting to add any primer. :|

I think my brain somehow ingnored them, maybe because my brain went "that can't be sink marks, not around all the windows, that would be silly, really around all the windows?". Or "I am already busy with those other sink marks over here, I will have to ignore this."

9 February 2020, 09:42

wilky
Having worked in a plastic injection molding factory that's a result of not enough pressure in the shot.
Obviously the machine operator hasn't informed the die setter of the issue.
Poor quality control
Total lack of care about the finished product

9 February 2020, 09:55

Treehugger
The issue seems to be where the plastic hull is at its thickest, because on the inside, more plastic is protruding. Would be nice to know if this is preventable, or not. It sounds like maybe it is preventable, by being more careful working with the injection mold machine (or maybe in the configuration of it).

The sink marks around all the windows aren't deep, but just enough deep to annoy.

9 February 2020, 10:16

wilky
It'd be the pressure of the shot.
Low pressure means not enough material is in the mold space.
Plastic cools and shrinks. This is why it's happening where it's thicker.
Hopefully it was detected during the run and not all kits are the same

9 February 2020, 10:42

Treehugger
Looking at the kit again I should correct myself. Six of ten windows have noticeable sink marks. I've already added primer and some color, but I think I will just bite it and sand off the paint and add the putty. :|

Thanks for the feedback. 🙂

9 February 2020, 12:39